Study of the calculating formulas in the minimum section of the gray casting iron pouring system
灰铸铁件浇注系统最小截面积计算公式研究
The injection molding flow of six different pouring system for air-condition panel was analyzed respectively by using Molding Plastics Advisers (MPA)software.
利用模流分析软件Moldflow Plastics Advisers(MPA)对空调机面板注塑模6种构型不同的浇注系统分别进行注射成型流动分析。
The structural characteristics of the aluminum alloy tap part were analyzed, and the design of pouring system and die-casting die structure were introduced.
分析了铝合金水龙头零件的结构工艺性特点,介绍了压铸模的浇注系统及模具结构设计。
Simulation and optimization of gating system of die-casting die for magnesium alloy AM60B part;
AM60B镁合金压铸模浇注系统的模拟与优化
Principle of Designing Gating System for Die Cast Aluminum Alloy Mould;
设计铝合金压铸模具浇注系统类型的原则
Optimization of Gating System for Gear Box of the Car Based on CAE System;
基于CAE分析的汽车齿轮室浇注系统的优化
concrete placement systems & equipment
混凝土浇灌系统与设备
Design and Analysis of the Routing Algorithm for the Intelligent Wireless Water-saving Irrigation System
智能无线节水浇灌系统的路由算法设计与分析
Application of PLC in Automatic Watering Control System at the Shed for Pepper;
PLC在大棚辣椒自动浇灌控制系统中的应用
Farmers increased their use of fertilizers and pesticide chemicals, and irrigation systems to water crops.
农民加强了化肥、虫剂的利用，并采用灌溉系统浇灌作物。
testing method for permanent of linear change on light weight castable refractories
轻量型可浇灌耐火材料线性变化系数测定方法
The Control Software developing of Lead ration pouring Microcomputer control System using weightlessness method
失重法铅锭定量浇铸系统软件设计
Design and Implementation of Ration Pouring System for Lead Anode Plate
铅阳极板定量浇铸系统的设计与实现
The Secondary Development of Autocad for Feed System of Injection Mold;
注塑模浇注系统的AutoCAD二次开发
Effects of Binders on Properties of Alumina Magnesia Based Castable
不同结合系统铝镁浇注料的性能研究
Design of Injection Mold Gating System of the Plastic Gear Based on MoldFlow Software
基于MoldFlow塑料齿轮注射模浇注系统设计
The Development Research of Gating System of Die Casting Based on Pro/Engineer
基于Pro/E的压铸模浇注系统开发
Design of Injection Systerm of Lost Foam Casting under Negative Pressure
消失模负压铸造浇注系统设计的探讨
Study on Gating and Riser System CAD Software Development
铸造浇冒口系统CAD软件的开发研究
Application of Fully-poured Bus in 6kV Auxiliary Power System
全浇注母线在6kV厂用电系统中应用
The Design and CAE Analysis in Multy-carities Injection Moding Feed System
多型腔注塑模浇注系统设计及CAE分析
Moldflow-based optimization analysis of gating system for umbrella framework
基于Moldflow的雨伞骨架浇注系统优化分析
Study on Gating System of Aluminium Alloy Shell Casting Based on CAE
基于CAE铝合金壳形件浇注系统的研究
Design of Gating System for Investment Casting Aerospace Components
熔模铸造航空件浇注系统设计和实践