This article described the basic process for design a external pressure vessel(including shell,elliptical head and cone) by the way in the ASME Ⅷ Div.
通过一个实例介绍了按ASME第Ⅷ卷第一分册中的规定———外压作用下带锥壳设备的设计过程,并给出了锥壳与筒体连接处截面组合有效惯性矩的计算方法。
Instability of bellows under external pressure with tensile displacement was researched by bellows instability tests and nonlinear finite element analysis.
对波纹管在拉伸条件下的外压稳定性进行了试验研究和非线性有限元分析 ,结果表明拉伸位移对波纹管的外压稳定性有不利影响 ,失稳是由于某一波纹局部区域的大量塑性变形而产生的。
Viscous inner and outer pressure forming of 1Cr18Ni9Ti specimen with thin-wall curved surface;
1Cr18Ni9Ti薄壁曲面件粘性介质内、外压力成形
In this paper, an alternative method employing inner and outer pressure with viscous media is proposed to form this kind of workpieces as a whole.
本文提出粘性介质内、外压力成形方法,可以直接整体成形薄壁曲面零件,不需要成形后的组合焊接,并针对直径变化比达35%的1Cr18Ni9Ti薄壁曲面零件进行了内、外压力成形实验和有限元分析,给出了变形过程粘性介质和坯料的流动规律和缺陷的预测分析,研究结果表明,薄壁曲面零件内、外压力成形是可行的。
Research on the experiment instrument and the characteristics of external pressure forming;
外压成形试验装置及成形特征研究
This paper analyzes the problem of extrapolated pressure in terms of.
对试井分析过程中的流量和时间取值问题,从流动时间与压力叠加以及有效时间和最终流量2个角度进行了分析,指出使用变流量、叠加时间和使用最终流量、有效时间得到的试井分析结果是一致的,联合采用有效流动时间和最终产量,能使复杂的问题得到简化,并且不失其准确性;从理论根源上对外推压力这一问题进行了分析,指出进行Horner压力恢复分析时必须考虑流动期间压力特性对于恢复压力曲线形态的影响,不同的生产流动特性会产生不同的外推压力,外推压力不是一个真实的压力值,其大小完全是任意的。
Researching on External Pressure Test Pressure Coefficient of External Pressure Vessels
薄壁外压容器外压试验压力系数研究
external pressure single type axial expansion joint
外压单式轴向伸缩接头
Uch a liquid in this form
喷雾器（如外压式的或内压式的）
A Tentative Study on the Relationship Among External Pressure,Vapor Tension and Boiling Point
外压与沸点和蒸气压的关系浅论(英文)
The stability of a large opening composites conic shell stiffened with nettings under axial compression, external pressure and their combination is calculated in this paper.
本文用有限元法计算了受轴压、压、及轴压和外压联合作用下的大开。
pressurized enclosure (Ex p)
正压外壳（Ex p）
Resistant to externally applied pressure.
坚硬的抵抗外来压力的
lifting jack (excl. hydraulic)
千斤顶（液压的除外）
hydraulic jack (excl. built in)
液压千斤顶（固定的除外）
horizontal action jack (excl. hydraulic)
水平千斤顶（液压的除外）
Torrington needle bearing
冲压外座圈滚针轴承
low pressure gas infrared heater
低压煤气红外加热器
epoxy encapsulated transformer
环氧树脂外包之变压器
external delivery point
(液压系统) 外接输出端
The pressure inside equals the pressureoutside.
内部的压力与外部的压力相等。
portable jack for vehicles (excl hydraulic)
车辆用轻便液压千斤顶（液压的除外）
Often,pressures from outside sources can cause stress.
来自外界的压力时常会导致重压感。
The Design of External Capacitor-Less CMOS Low Drop-Out Voltage Regulator;
无片外电容CMOS低压差稳压器的设计