The significance of setting the cone angle is revealed by analyzing the relationship between the stator cone angle of annular gap mill (AGM) and the intensity of materials being abraded The simplified model of motion and that of dynamics have been established and the cone angle of stator arrived at.
通过分析环缝磨定子锥角与被研磨物料强度之间的关系 ,揭示出设定锥角的意义 ;建立了磨料介质的简化运动模型和力学模型 ,求解出定子锥角。
Analysis of influence of material strength on the behavior of UPC beams;
材料强度对UPC梁性能影响分析
Statistical inference of material strength of existing structures;
现有结构材料强度的统计推断
The conclusions are:①Material strength has influence,to a certain extent,on the treatment effect on fatigue performance of welded joints treated by ultrasonic peening.
对大量超声冲击处理焊接接头的试验结果进行分析总结,探讨超声冲击焊接接头疲劳设计与原始焊接接头的差异,并得到下述结论：①材料强度对超声冲击方法改善焊接接头疲劳性能的处理效果有一定影响,随着接头材料强度的提高改善效果也越好,因此采用低强钢超声冲击处理焊接接头的疲劳试验结果得到疲劳设计S—N曲线是安全的。
Constructed math model based on neural network for predicting clinker strength.
本文利用神经网络建立预测水泥熟料强度的数学模型,并用MATLAB6。
Clinker strength prediction in cement factory is a subjective process.
指出目前水泥厂预测熟料强度的主观性,提出利用粗糙集中的可辩识矩阵对熟料强度影响因素进行计算,能够选取出对强度贡献较大的主要影响因素。
Effect of heat treatment temperature on crack-healing and bending strength of SiC/Si_3N_4 composites
愈合温度对SiC/Si_3N_4复合材料强度的影响
The key material is amply strong.
键材料的强度足够。
These materials exhibit low strength.
这些材料具有低强度。
Carbon materials--Determination of the compressive strength
GB/T1431-1985炭素材料耐压强度测定方法
alternating bending strength
(包装材料反复扭折的)耐折强度
Wwlding material: low carbon steel, high strength steel, medium carbon steel, low alloy steel.
可焊接材料：低碳钢、强度钢、碳钢、合金钢。
brittle materials tensile-strength tester
脆性材料抗拉强度测试仪
method of test for crushing strength and modulus of rupture of castable refractories
可浇灌耐火材料抗压强度测定
test method for puncture strength of geotextiles and their related products
土工布相关材料的击穿强度试验法
The strength of material is usually obtained by laboratory tests.
通常由实验室的试验得到材料的强度。
STATISTICAL FA RE PREDICTION MODELS FOR ST UCTURAL CERAMICS
结构陶瓷材料断裂强度统计预测模型
Tensile Strength of C/Al Composites at High Temprature
碳(石墨)/铝复合材料的高温拉伸强度
A Study on Distribution Function of Fatigue Strength for the Roller Chain Material
滚子链材料疲劳强度分布函数的研究
Study of the Drillability of NM360 High-strength Steels;
NM360高强度材料钻削性能研究
Tensile Bond Strength between the Tray Material and Impression Material: An in Vitro Study;
印模材料和托盘间固位强度分析研究
Macro- and Micro-mechanics Strength Analysis of Composite Structures;
复合材料结构宏、细观强度破坏分析
Structure Strength Analysis of New Type Composite GFRP Kuppe;
新型复合材料玻璃钢导流罩强度分析
Research on Strength and Vibration of Composite Propellers;
复合材料螺旋桨桨叶强度与振动分析