More similar to the plate tectonic activity, the fault blocks between the strike\|slip fault plane converge near the constraining bend and diverge near the releasing bend.
研究认为 ,岩石圈断块沿郯庐断裂的走滑活动与大型板块构造的活动方式有一定的相似之处 ,即伴随着郯庐断裂的右行走滑 ,从断裂的增压弯曲部位到断裂的释压拉张部位将发生岩石圈断块的汇聚与离散现象 ,由此造成了走滑断裂带上增压弯曲部位与释压拉张部位局部应力场性质的不同 :增压弯曲部位应力相对集中 ,岩石圈断块发生汇聚、挤压、隆升 ;而释压拉张部位由于应力释放 ,岩石圈断块发生离散、伸展、沉降。
Compression bending of metal sections, as a newly-developed method of 3D bending process, has gradually come into practical application in automotive industry.
近年来,一种新的弯曲技术——压缩弯曲开始进入了实用阶段。
The cold-pressed bending process of the semi-shell of the rear part of the stamping andwelding,driving axle,the structure and the working process of the cold stamping bending die forforming the forming shell,and the design of the main accessories and parts are introduced.
介绍了80kN汽车冲焊驱动桥后桥半壳冷冲压弯曲成形工艺、模具结构及其工作过程,以及主要零部件的设计,指出了模具设计及使用过程中应注意的事项。
Research of Wood Compression and Bending Control System Based on PLC and HMI;
基于PLC和触摸屏的压缩弯曲木自动控制系统研究
Investigation on Compression and Bending Behavior of Tubes Filled with Open-cell Aluminum Foam
开孔泡沫铝夹芯管压缩与弯曲力学行为的研究
Effect of Hydrothermal-Microwave Treatment on Softening and Longitudinal Compressing and Bending Elm Wood
水热-微波处理对榆木软化和顺纹压缩及弯曲的影响
Crouch down
曲膝弯腰以便少占地方，卷缩，弯腰低头
The normal state of elastic tension or partial contraction in resting muscles.
正常伸缩性安静的肌肉所具有的正常的受压伸缩或局部弯曲的能力
Bending behaviors of functionally gradient piezoelectric curved cantilever was studied.
研究了弯曲型梯度功能压电悬臂梁的弯曲特性。
Effect of bending angle on hydroforming of curved hollow components
弯曲角度对弯曲轴线件内高压成形的影响分析
A shortened narrow bend, often signifying bastardy.
缩短的弯曲窄条，常表示私生子地位
The relationship between compressive strength (flexural strength) with ice temperature, stress and direction is analysed in the paper.
分析了海冰的压缩强度和弯曲强度与冰温、应力率和加载方向的关系。
curve tube pressure balance expansion joint
曲管压力平衡伸缩接头
crankcase compression engine
曲轴箱压缩式发动机
open crank case compressor
敞开式曲轴箱压缩机
DISCUSSION ON THE NECK BENDING STIFFNESS OF WORK ROLLS IN THE HYDRAULIC BENDING ROLL CONTROL SYSTEM
液压弯辊控制中工作辊辊颈弯曲刚度探讨
To bend, warp, or crumple, as under pressure or heat.
由于受压或受热而弯曲，起皱
The branches were bending with the weight of the fruit.
树枝被果实的重量压得弯曲了。
The floor buckled up under the weight of so many people
地板在这么多人的重压下弯曲了。
Research and Development on Sheet Metal Bending Parts CAPP System;
冲压弯曲件CAPP系统研究与开发
Study on elastic distortional buckling of lipped channel beam-columns
卷边槽钢压弯构件弹性畸变屈曲研究