The advantages of vacuum spraying are that the said active feed additives not only can be avoided from thermal processing but also can permeate into pellets, therefore their activity can be reserved to a maximum, bring their functions into full play.
真空喷涂技术的优点是可以让上述活性饲料添加剂避免热加工过程,并渗透到颗粒内部,最大限度地保留活性,发挥功能。
In order to reduce microecological preparation loss during the manufacture of compound feeds,a series of experiments taking Bacillus subtilis as an example were carried out based on vacuum spray technology.
以枯草芽孢杆菌为研究对象,考察了真空后喷涂系统对颗粒间均匀性及颗粒内外均匀性的影响因素。
In this article, based on the problems in the use of the film dropping evaporation equipment and with RNJM03-4200 third Film Dropping Evaporation Equipment as the example, one method of appropriate disposition of the vacuum device was introduced.
以ＲＮＪＭ０３－ ４２００ 型三效降膜式蒸发设备为例，针对近些年来降膜式蒸发设备真空装置出现的问题，就如何合理配置真空装置予以描述。
The vacuum device for three-effect and four-compartment evaporation process of diaphragm caustic soda was transformed,which reserved the water jet condensers and added a combined vacuum device of a surface condenser and a vucuum pump.
对隔膜法烧碱三效四体蒸发工艺的真空装置进行改造,保留水喷射冷凝器,增加表面冷凝器加真空泵的真空装置,提高了真空度,降低了蒸汽消耗。
Design of Control System for Vacuum Pressure Casting Mould Based on LOGO!;
基于LOGO!的压铸模具真空装置控制系统设计
Aimed at the pore deficiency of conventional pressure casting,a vacuum of mould based on LOGO! controlled is designed.
针对传统压力铸造的气孔缺陷,设计了一套基于LOGO!控制的模具真空装置,并从总体方案、气路部分、控制部分三方面较详细的介绍了设计方法。
A module made by the deposition of magnetic alloys in a vacuum and under the influence of a high magnetic field.
一种用磁合金以真空喷涂并在高磁场的作用下制成的组件。
Study on the vacuum infusion parameters of spraying liquid phytase water solution to extruded pellets
膨化颗粒饲料液体植酸酶水溶液真空喷涂工艺参数研究
STUDY ON LIQUID ADDITION UNDER VACUUM POST PELLETING OF FEED;
颗粒饲料液体真空后喷涂工艺的研究
Spraying method whether by air spray, airless spray, hot air spray or hot airless spray should be in accordance with the following.
空气喷涂，无空气喷涂，热空气喷涂或无空气热喷涂均应遵循以下原则。
Study on workspace analysis and simulation of 6-DOF painting robot based on monte-carlo method
基于蒙特卡洛法的喷涂机器人工作空间分析及仿真
high pressure airless heating pasted type spraying machine
高压无空气加热厚浆型涂料喷涂机
water jet vacuum
水喷真空 -用喷射泵能达到的真空
New models of spray gun and simulation in spray painting
喷涂过程中喷炬新模型的建立及仿真研究
Micro-plasma Sprayed Hollow Mullite Thermal Barrier Coatings
微弧等离子喷涂制备空心莫来石隔热涂层研究
Properties and Application of WC Coating Prepared by High Velocity Air Fuel
空气助燃超音速火焰喷涂WC涂层的性能及应用
Simulation of the Spray Booth Flow Field of Painting Line with Solidworks
基于Solidworks的涂装线喷漆室流场仿真分析
Construction Design and Simulation of a Kind of Spraying Robot;
喷涂机器人操作机方案设计及仿真分析
Simulation model test of spraying polyurea as anti-seepage layer on 300-m high arch dams and its application
300m级拱坝喷涂聚脲防渗仿真模型试验及应用
Experimental Study and Spray Process Simulation of Ceramic/Metal Gradient Wear Resistance Coating;
陶瓷/金属梯度耐磨涂层的实验研究及喷涂过程仿真
Discussion on spay section design of air handling unit for automobile painting line
汽车涂装线空调机组喷淋段的设计探讨
A study and application of composite grouting material as air tight coating material in entries retained at gob-sides
沿空巷道喷涂隔风复合浆体材料研究及应用
The coating is sprayed onto the specimen, air-dried to a soft powder.
这种涂料喷涂到试件上去并在空气中干燥之后，即成为松软的粉末。
Study on Arc Spraying Technology and the Performance of Spray Coat;
电弧喷涂工艺及喷涂涂层性能的研究