Analysis of Zn Build up in Lubricated Friction Wear Tests for High Al-Zn Base Alloy;
高铝锌基合金摩擦磨损试验中增重原因分析
Study of surface strengthening technology and wear test of diesel engine cylinder liner
柴油机气缸套表面强化工艺及磨损试验的研究
The physical chemical properties of the diesel engine oil samples obtained from various blending ratios with same additive formulation were proceeded the crankcase simulation, oxidation stability and wear tests.
为了用中东原油生产润滑油基础油 ,使用相同的添加剂配方 ,将经传统工艺制得的伊朗减四线和大庆减四线基础油按照不同的质量比例调制成 40CC级柴油机油油样 ,分别进行理化性质测定、曲轴箱模拟试验、内燃机油氧化安定性试验和抗磨损试验。
This paper illustrates the principle of the inner cone grinding twist drill and the process of grinding experiments on the tool grinder.
通过试验刃磨出了合格的麻花钻,验证了内锥面法刃磨麻花钻理论,并对内锥面刃磨试验中存在的问题进行了分析讨论。
German AG company, with the help of erosive abrasion tester, tested the wear abrasion rate on different abrasion-resistant materials thr.
德国AG公司使用冲蚀磨损试验装置,以不同的冲蚀角、不同的冲蚀速度和不同混合比的料流冲击试验样,测试了不同耐磨材料的磨损率;并对磨损数值进行了分析比较。
The paper analyzes the mechanism of fly ash abrasion phenomena met with in CFBBs, accompanied by a report on abrasion tests on typical membrane linings, performed with various impact angles of the medium.
该文对循环流化床锅炉内飞灰磨损的机理进行了分析 ,并用磨损介质在不同的冲刷角度下对循环流化床典型膜式壁炉衬进行了磨损试验研究。
Coating abrasion test showed that the wear-resisting property of samples could be improved greatly.
磨损试验表明,用掺入微纳米MoC粉体的喷涂粉喷涂样品表面,样品耐磨性显著提高。
rotary abrasive tester
旋转式磨料磨损试验机
block-on-ring wear test
试块－试环滑动磨损试验
Metallic materials-Wear tests-MM mode wear test
GB/T12444.1-1990金属磨损试验方法MM型磨损试验
Metallic materials-Wear tests-Block-on-ring wear test
GB/T12444.2-1990金属磨损试验方法环块型磨损试验
The Research on Abrasive Wear of 60Si2Mn Steel by Alfalfa Powder
60Si2Mn钢抗苜蓿草粉的磨料磨损试验研究
Experiment of Metal Materials Abrasive Wear for Alfalfa Powder
苜蓿草粉对金属材料的磨料磨损试验
Study Abrasive Tester and Effect of Loads on High Chromium Cast Iron;
磨损试验机的研制及载荷对高铬铸铁磨损研究
The Design and Experimental Study of the Friction and Abrasion Testing Machine for the Pumping Rod s Centralizer;
抽油杆扶正器摩擦磨损试验台的研制及摩擦磨损试验研究
The Best Experiment Program of Cylinder Wears by Means of the Orthogonal Test
用正交试验法研究汽缸套磨损试验的最优方案
Test method for wear of plastics by rolling
GB/T5478-1985塑料滚动磨损试验方法
Test method for friction and wear of plastics by sliding
GB/T3960-1983塑料滑动摩擦磨损试验方法
The Study of Computer Simulation Method Based on Pin-on-Disc Wear Test;
销盘磨损试验的计算机仿真方法研究
Design of wear testing machine control system based on the LabVIEW
基于LabVIEW的磨损试验机测控系统设计
Development of WFM reciprocating friction wear testing machine
WFM型往复式摩擦磨损试验机的研制
Abrasion-resistant capability of Ni-cast iron and Cr-cast iron were studied by abrasion wears and impact test.
对镍硬铸铁和常用的铬系白口铸铁进行了削盘磨损试验和冲击磨料磨损试验。
Development of High Speed Electric-tribometer and Researches on Tribo-electric Behaviors of Strip Materials;
载流摩擦磨损试验机的研制及滑板材料摩擦磨损和载流性能研究
Development of Dynamic Load Wear Testing Machine and Material Wear Experiment Investigation;
振动载荷磨损试验机的研制及材料磨损性能研究
Development of the Intelligent Testing System for MHK-500 Ring-Block Tribometer;
MHK-500环块摩擦磨损试验机智能测试系统的研制