Highlight is given to the isolated air bag,pressurizing assembly,locking unit,fastening unit and air circuit system.
分析了以独立气囊为加压元件的QYJ200-160型气压摇架的结构特点,重点从独立气囊、加压组件、锁紧组件、固紧机构和气路供应及其控制系统几个方面详细对该气压摇架的结构进行了分析,并分析了棉型细纱牵伸的型式及技术特征,其直压式加压组件加压准确、互不干扰、调节方便;采用四连杆式后锁紧机构,"哈夫"式握持空心方形支管轴的紧固机构,锁紧可靠、操作轻便;摇架体高度偏心调节轴和活塞阀门式的气路控制系统,结构新颖。
Based on the simulation software Abaqus,the numerical simulation of rolling process of conical ring with inner steps was taken.
以Abaqus三维有限元模拟软件为平台,对内台阶锥形环件的轧制过程进行了数值模拟,通过模拟计算揭示了内台阶锥形环件轧制缺陷的形成机理。
The numerical simulation of hot rolling process of LD10 aluminum alloy conical ring with inner steps was taken based on the experimental data.
采用Gleeble3500热模拟实验机进行了压缩实验,分析了LD10铝合金的高温力学性能;在D51-160热轧环机上进行热轧实验,确定了LD10铝合金环件初始轧制温度为470℃;以实验数据为基础,对LD10铝合金内台阶锥形环件的热轧过程进行了数值模拟,分析了LD10铝合金内台阶锥形环件轧制缺陷形成机制,并对预轧制环件进行了设计;通过热轧实验对数值模拟结果进行了实验验证。
Countersunk external toothed lock washer for assembly
GB/T9074.28-1988组合件用锥形锁紧垫圈
Cross recessed countersunk head screw and countersunk serrated external toothed lock washer assemblies
GB/T9074.9-1988十字槽沉头螺钉和锥形锁紧垫圈组合件
Cross recessed raised countersunk head screw and countersunk external toothed lock washer assemblies
GB/T9074.10-1988十字槽半沉头螺钉和锥形锁紧垫圈组合件
Specifications for spring washers--Toothed lock and serrated lock washers
GB/T94.2-1987弹性垫圈技术条件齿形、锯齿锁紧垫圈
Lock washers external teeth
GB/T862.1-1987外齿锁紧垫圈
Lock rings with cone pin
GB/T883-1986锥销锁紧挡圈
Serrated lock washer external teeth for assembly
GB/T9074.27-1988组合件用外锯齿锁紧垫圈
Flared type tube fittings--Back-up washer
GB/T5652-1985扩口式管接头锁紧螺母垫圈
Washers with cone face
GB/T850-1988锥面垫圈
Hexagon head bolt and serrated lock washer external teeth assemblies
GB/T9074.16-1988六角头螺栓和外锯齿锁紧垫圈组合件
horse shoe washer
开口垫圈,马蹄形垫圈
Cross recessed pan head screw and serrated lock washer external teeth assemblies
GB/T9074.2-1988十字槽盘头螺钉和外锯齿锁紧垫圈组合件
Lock rings with screw and circlip
GB/T885-1986带锁圈的螺钉锁紧挡圈
A wide range of standard stampings, non-standard products, stainless steel washers, internal/ external teeth washers, rings, circlips for holes, circlips for shaft, other fasteners, fittings, seal washers and clamps主要生产各种标准件冲压件.各种非标产品.
不绣钢垫圈;内外齿垫圈;挡圈;孔用挡圈;轴用挡圈;纱嘴头,其他紧固件、接件密封垫圈卡圈.
Lock ring with scre
GB/T884-1986螺钉锁紧挡圈
Curved spring washers
GB/T860-1987鞍形弹性垫圈
Curved single coil spring lock washers
GB/T7245-1987鞍形弹簧垫圈
Wave single coil spring lock washers
GB/T7246-1987波形弹簧垫圈