Development of rubber seal ring with outer case for push-pull rod;
推拉杆用外嵌骨架橡胶密封圈
Performance analysis of special cross section rubber seal ring;
特殊形状橡胶密封圈的性能分析
The ageing and durability of rubber seal ring for pipe joint were briefly discussed in this paper.
针对管道接口用橡胶密封圈的老化原因和耐久性进行了探
Study of rubber ring with inner case resistance to high temperature;
内骨架耐热橡胶密封圈的研制
This paper introduces a new type of quick connector framework by making use of rubber seal and plastics clip.
介绍了一种利用橡胶密封圈和塑料卡环实现待插管锁紧的新型快插式接头结构。
Analysis on contact deformation and stress for rubber O-sealing ring;
橡胶O形密封圈的接触变形及应力分析
With the help of commercial finite element analysis code,ANSYS, a nonlinear finite element model for rubber O-sealing ring and its groove were set up.
借助于大型有限元分析软件ANSYS,建立了橡胶O形密封圈与沟槽接触的非线性有限元分析模型,分析了橡胶O形密封圈的尺寸公差对密封性能的影响,以及密封圈的内径伸长率和压缩变形率改变时,接触面上最大接触应力的变化情况,从而为进一步可靠设计、优化橡胶O形圈提供了理论依据。
rubber sealing ring for medical sterite cooker
医用消毒锅橡胶密封圈
rubber sealing ring for pressure cooker
日用压力锅橡胶密封圈
Effects of Dimensional Tolerance on Sealing Characteristic of O-ring;
O形橡胶密封圈尺寸公差对密封性能的影响
Finite Element Analysis on Rubber Sealing Y-ring in the Condition of Static Seal
静密封条件下Y形橡胶密封圈有限元分析
Test methods for rubber O rings
GB/T5720-1993O形橡胶密封圈试验方法
Appearance quality for reciprocating rubber seals
GB/T15325-1994往复运动橡胶密封圈外观质量
Finite Element Analysis of Stress and Contact Pressure of Rubber O-sealing Ring with Back-up Ring
O形橡胶密封圈配合挡圈密封的应力与接触压力有限元分析
Reciprocating rubber seals-Design criteria for standard applications-Part 3: rubber seals for wipers
GB/T10708.3-1989往复运动橡胶密封圈结构尺寸系列第三部分:橡胶防尘密封圈
Appearance quality acceptance criteria for rubber O-rings
GB/T3452.2-1987O形橡胶密封圈外观质量检验标准
The Non-linear Contact Finite Element Analysis of the Mouth Shaped Rubber Sealing Ring
唇形橡胶密封圈非线性接触有限元分析
Study on Effects of Biodiesel on Swelling Performance of Rubber Sealing Collar
生物柴油对橡胶密封圈溶胀性能的影响研究
The Application of Finite Element Method in the Design of Rubber Sealing Y_X-ring
有限元分析法在Y_X形橡胶密封圈设计中的应用
Research on Storage Life of Silicon Rubber O-ring in Different Temperature and Humidity Condition
不同温、湿度条件下硅橡胶密封圈贮存寿命研究
" Fluid systems--Sealing devices--O-rings--Inside diameters, cross-sections, tolerances and size identification code"
GB3452.1-1992液压气动用O形橡胶密封圈尺寸系列及公差
Fluid power systems--O-ring--Design criteria for O-ring housing--Basic calculation
GB/T3452.3-1988液压气动用O形橡胶密封圈沟漕尺寸和设计计算
Simplified two-dimension finite element model was established for the hollow rubber seal of hood-type annealing furnace.
建立了罩式退火炉空心橡胶密封圈的二维简化有限元模型;
Improvement on Rubber Seal Ring of Plastic Bottle-blower Based on Finite Element Method
基于有限元分析的PET吹瓶机橡胶密封圈的改进设计
Medium or High-pressure Seal Design of SrO·6Fe_2O_3 MNBR
SrO·6Fe_2O_3磁性丁腈橡胶中高压密封圈设计