Finite element analysis on the bending stress for roller spur bevel gear based on ANSYS;
基于ANSYS的滚齿直齿圆锥齿轮弯曲应力有限元分析
Analysis of tooth root bending stress for spiral bevel gears;
弧齿锥齿轮齿根弯曲应力分析
Calculation of bending stress of steel-concrete composite beam considering slippage effect;
考虑滑移效应的钢—混凝土组合梁弯曲应力计算
The article anaylses the skew arch roofing s bend stress under symmetry and unsymmetrical loads,calculates the skew arch roofing critical load under the symmetry and unsymmetrical loads,the result indicates the skew arch roofing s resistance,and stability are sufficient for its use.
分析了在对称和非对称载荷作用下斜拱型屋面弯曲应力,计算了在对称载荷和非对称载荷作用下斜拱型屋面临界载荷。
This paper demonstrate the way how to measure and control D max -D min of the pressure cylinder for its safe working,which is started with the circular additional bend stress which is caused by the non circularity of the pressure cylinder,then it points out a new method of controlling strength of the pressure cylinder.
从压力容器不圆度引起周向附加弯曲应力出发 ,推导出检测和控制不圆度值的方法 ,使其达到其安全工作的目的 ,为工业生产及检测部门提供依
This paper points out a proplem in《Mechanial Design of Forestry Engirieer-ing》Writted by Fu Wenfan that formula in calculating the bend stress of the hook.
本文指出了傅文范等著《森林工程机械设计》（绞盘机）中涉及到的关于吊钩钩身弯曲应力公式存在的问题，并根据有关理论，提出比较符合实际的计算吊钩钩身弯曲应力的公式。
Software Development on Finite Element Analysis for Bending Stresses of Transmission Gears;
变速器齿轮弯曲应力分析有限元软件的开发
It has been shown that bending stresses that inadvertently occur due to misalignment between the applied force and the specimen axes during the application of tensile and compressive forces can affect the test results.
在材料拉伸和压缩试验期间,由于加力轴线与试样轴线不同轴产生弯曲应力,影响试验结果。
The remote bending stress at the plate surface was measured.
板表面处的远场弯曲应力已被测出。
The bending stress is zero for the element at B.
在B处的单元体，弯曲应力为零。
Layered-Slipping Model for Bending Stress Analysis of Stay Cables;
考虑分层滑移的斜拉索弯曲应力分析
Modeling and Simulation for Bending Stress Analysis of Transmission Gears
变速器齿轮弯曲应力分析建模与仿真
Bending Stress of Cross-section in Track of Hydraulic Steel Gate
水工钢闸门轨道横截面弯曲应力分析
STUDY ON BENDING STRESS OF MAIN CABLE IN LONG-SPAN SUSPENSION BRIDGE
大跨度悬索桥主缆弯曲应力试验研究
Find the value of the bending stress and the deflection at the center if the ribs are omitted.
如果略去肋条，求中心处的弯曲应力和挠度之值。
Research on Tooth Profile Generation and Bend Stress Analysis of Face-gear Drive;
面齿轮传动的齿面生成和弯曲应力分析
Software Development on Finite Element Analysis for Bending Stresses of Transmission Gears;
变速器齿轮弯曲应力分析有限元软件的开发
Researches on High Dynamic Application of Flexible Printed Circuits;
挠性电路板在高弯曲应力中的试验研究
Finit Element Analysis on Bending Stress of Pin Gear Fit Pin Tooth and Wheel Tooth;
销齿副销齿和轮齿弯曲应力有限元分析
Eular crippling stress
（纵向弯曲）欧拉临界应力
The CAT System of Normal Stress in Crossbeam Wind
横梁弯曲正应力计算机辅助测试系统
Interlaminar Stresses of a Laminated Composite Bar under Bending (Ⅰ)
叠层复合材料杆弯曲的层间应力(Ⅰ)
Inspection Rules Used in Drawing Diagrams of Internal Bending Force;
绘制弯曲内力图的“四查”规则及其应用
flexural strain
挠曲应变,弯曲应变
incapable of or resistant to bending.
不能弯曲或者对弯曲有抵抗力。
The frictional restraint to bending has an effect on bending.
弯曲的摩擦约束力对弯曲有影响。