Research on detection of planing cutting resistance;
刨削式切割阻力测定的研究
The reason of planer tool concession produced in planing the inner ape rture keyslot of wheel hub of two wheel tractor is analyzed, and the planing lim it deep and the intension of the tool holder are calculated.
分析了手扶拖拉机车轮毂内孔键槽刨削加工时产生“让刀”现象的原因 ,并对内孔键槽的刨削极限深度、刀杆强度等进行计算与校核 ,提出了轮毂内孔键槽刨削的最佳切削参数。
Then,by comprehensively analyzing the planing process and by investigating the effects of cutting parameters on the planing process,reasonable processing parameters were determined.
采用刨削加工法,利用多齿刀具在普通刨床上加工获得质量稳定的微细金属纤维,纤维的长度为10~22mm,直径可达100μm以下。
Study on Machining Twisted Impeller of Roots Blower with NC Shaping Machine;
罗茨鼓风机扭叶转子数控刨削加工的研究
Study on Manufacturing Technique of the Inner Helical Surface
内螺旋曲面包络刨削加工位置的计算研究
Shaping and planing produce flat surfaces with a single-point cutting tool.
仿型刨削和牛头刨削用单刃刀具加工平面。
Mechanical shear components, the need for edge processing, shaving its capacity of not less than 2.0 mm.
气割或机械剪切的零件，需要进行边缘加工时，其刨削量不应少于2.0㎜.
The paper introduces a new type composing lathe of finger joint splicing board surface- sprial cutter head Planer andsander, and also states the cutting and clipping priciple and good points.
文章介绍了一种新型指接拼板表面加工的组合机床─螺旋刀刨砂机，阐明了它的切削原理和优点。
The processing method of knife support parts in bamboo flaker
竹材刨片机中“刀片支撑座”的加工
In shaping, the cutting tool on a shaper reciprocates or moves Back and forth while the work is fed automatically towards the tool.
在仿型刨削操作中,仿型刨床上的刀具作往复或前后移动的同时,工件被自动推向刀具。
a woodworking plane designed to cut rabbets.
用来刨槽口的木工刨。
a carpenter's plane intermediate between a jack plane and a jointer plane.
介于粗刨和接缝刨之间的一种木工刨。
planed or worked along the edges to facilitate assembly board of coniferous wood
针叶树木板，经沿边缘刨平或加工以便于装配
Sliver of Thin Slice Digs the Flowered Numerical Control Processingprocess Monitor System Research;
长条薄片刨花数控加工过程监测系统研究
Study on the Forming Principle of the Cutting Burr in Turning
车削加工中切削毛刺生成机理的研究
Identification of Cutter Breakage in Variable Cutting Parameters Milling;
变切削参数铣削加工中刀具破损辨识
Identification of Cutter Wear in Variable Cutting Parameters Milling;
变切削参数铣削加工中刀具磨损辨识
Cutting Force Modeling in Turning Based on Cutting Parameters in Face Cutting;
基于切削参数的端面加工切削力模型
relative machinability
相对切削性, 相对加工性
machining of difficult-to-cut metals
难加工金属材料的切削
vertical turner flexible machine cell
立式车削柔性加工单元