Effect of sintering temperature on performance of low-heat Portland cement and its mechanism;
烧成温度对低热水泥性能的影响及其机理研究
By means of DTA and XRD, the influence of sintering temperature on the formation and properties of C2.
利用DTA和XRD方法,研究了烧成温度对硫铁铝酸钡钙矿物性能的影响。
The microstructure and the room-temperature resistivity of BaTiO3-based PTC in different sintering temperature(1280℃,1300℃,1320℃) was observed by SEM.
实验以常用电子陶瓷工艺制备BaTiO3基PTC材料时,通过观察不同烧成温度(分别为1280℃,1300℃,1320℃)的PTC材料的阻温曲线并且通过扫描电镜(SEM)观察其显微结构,发现烧成温度越高,晶粒发育的越好,并且烧成温度升高,材料出现过烧现象,材料的玻璃相和气孔率增大,从而室温电阻率增大。
The relationship of the porous ceramics properties with firing temperature and the main materials particle size is also discussed.
本研究以石英和长石为主要原料 ,通过控制石英和长石的粒度和配比 ,研制出一种高强度的微米级多孔陶瓷 ,并讨论了骨料粒径和烧成温度与其性能之间的关系。
The influence of firing temperature on the structure and electrical properties of tin oxide conductive ceramic were researched by using X ray Diffraction and measuring electrical properties.
本文通过 X-射线衍射分析及阻温特性测定等方法研究了 Sn O2 导电陶瓷的晶相组成和电性能与烧成温度的关系。
The firing temperature varied in a.
陶器的烧成温度从新石器时代的７５０～８００℃，延续至春秋战国时期的１０５０～１１５０℃，到东汉的１１５０～１２００℃。
The result shows that the ball sintering temperature decreases,while sintering temperature range enlarges with the pressure increase;the highest density and the lowest wear rate is obtained at the pressure of 100MPa.
结果表明:在本研究系统内随着压力的增加,瓷球的烧结温度下降,烧成温度范围拓宽。
Effect of the sintering temperatures on the structure and performance of synthesizing mullite membrane
烧成温度对合成莫来石陶瓷膜的影响
STUDY ON MICROSTRUCTURE OF ELECTRICAL PORCELAIN AT DIFFERENT SINTERING TEMPERATURES
不同烧成温度下电瓷微观结构的研究
Using Wollastonite to Decrease Firing Temperature of Table Ware
利用硅灰石降低日用陶瓷烧成温度的研究
INVESTIGATION ON TECHNOLOGICAL CONDITION OF LOWERING FIRING TEMPERATURE OF QINZHOU NIXING POTTERY
降低钦州坭兴陶烧成温度的工艺条件研究
THE INFLUENCE OF FORMING PRESSURE AND FIRING TEMPERATURE ON PRODUCING CLOSED POROSITY CERAMICS USING SOLID RESIDUE AND TAILINGS
成型压力和烧成温度对利用废渣和尾矿制备闭孔发泡陶瓷的影响
Effects of calcination temperature and zirc on addition on properties and microstructures of magnesia-spinel refractories containing lightweight aggregate
烧成温度和锆英石对轻骨料镁尖晶石材料性能和显微结构的影响
Color results will vary according to glaze composition, firing temperature and kiln atmosphere.
唯基础釉的组成物料、烧温度、氧化或还原均会影响烧成的颜色。
The Study of the Preheating Temperature for Selective Laser Sintering Forming Machine;
选择性激光烧结成形机预热温度的研究
Effect of Calcination Temperatures on Spinel LiMn_2O_4 Prepared by Solution Combustion Synthesis in Nitrate System;
温度对硝酸盐体系液相燃烧合成产物LiMn_2O_4的影响
Effect of Fuel Content and Temperature on Spinel LiMn_2O_4 Prepared by Solid-State Combustion Synthesis
燃料量和温度对固相燃烧合成LiMn_2O_4的影响
Effects of catalysts and calcination temperatures on synthesis of SiC fibers
催化剂及煅烧温度对合成SiC纤维的影响
Effect of sintering temperature on phase composition and microstructure of Y_2Ba_4CuNbO_x powder
烧结温度对Y_2Ba_4CuNbO_x粉体物相成分及显微结构的影响
Preparation and Numerical Simulation for Temperature Field of Composite Ceramics by Combustion Synthesis Process
燃烧合成复合陶瓷制备及固化过程温度场模拟
He has a fever and a temperature of 38.5 degree.
他发烧，体温38.5摄氏度。
The Mathematics Model of LTCC Sintering Furnace Temperature Field
低温共烧陶瓷专用烧结炉温度场的数学模型
Study on Numerical Simulation and Optimization of Temperature Field in Nitride-production Furnace;
氮化制品烧成窑内温度场的数值仿真及优化研究
Study on Numerical Simulation of 3D Temperature Field during Selective Laser Sintering Polymer-coated Metal Powder;
覆膜金属粉末激光烧结成型过程三维温度场数值模拟技术研究
Study of Key Technologies of Selective Laser Sintering Processing Based on Temperature Field;
基于温度场的选区激光烧结成型工艺关键技术研究