Simulation analysis and bending die design of supporting frame;
支架模拟分析及其弯曲模设计
Techniques about decreasing rebound in the structural design of bending die;
弯曲模结构设计中减小回弹的技巧
Preparation and flexural modulus of biodegradable composites reinforced with kenaf fibers;
洋麻纤维增强全降解复合材料的制备及其弯曲模量
Biodegradable composites reinforced with bagasse fibre were prepared by a press forming,and the thermal properties of fibre and the flexural modulus of composites were investigated in view of the fibre content and length.
利用压制成型制备了甘蔗渣纤维增强可降解复合材料,分析了纤维的热分解性能,研究了纤维含有量和纤维长度对材料弯曲模量的影响,利用Cox剪滞法和材料的结构特点,探讨了一种新的修正模型对弯曲模量的预测。
The flexural strength and flexural modulus will reach the maximum value of 130 MPa and 4.
分别研究了丙烯腈基短切碳纤维含量、引发剂(过氧化苯甲酰,BPO)用量和HA的质量分数对复合材料弯曲强度和弯曲模量的影响。
In this paper, the internal friction of foamed Al-Si alloy(ZL104) in different bending modes was investigated, for getting the characteristics of the internal friction of foamed metal in different boundary conditions.
为了获得不同边界条件下泡沫金属的内耗特征,通过采用动态机械分析仪在不同弯曲模式下对泡沫铝硅合金的内耗进行实验研究。
Study of Springback for Design of the Tool in Big Sheet Metal Forming;
大型板材弯曲模具设计中补偿弯曲回弹变形的研究
The Construction Design of the Bending Die for Improving the Surface Finish of Parts;
提高工件表面质量的弯曲模结构设计
Profile design for stretch bending die of extrusions considering springback
考虑弯曲回弹的拉弯模外形设计方法
Finite Element Simulation for Laser Curve Forming of Sheet Metals;
板料激光曲线弯曲成形的有限元模拟
EXPERIMENTAL STUDY ON THE FLEXURAL STRENGTH OF FINE GRAIN ETHANOL MODEL ICE
细粒酒精模型冰的弯曲强度试验研究
Mechanical model and analysis of casing bucking in horizontal wells
水平井套管弯曲力学模型与计算分析
Study on Variational Principles of Springback for Bending and Its Numerical Simulation;
弯曲回弹变分原理及其数值模拟研究
Characterization and Modeling for Bending Behaviour of Yarns and Fabrics in-Situ;
纱线与织物同机弯曲表征及建模分析
Experimental Study and Simulation on Laser Bending of Tubes;
管材激光弯曲成形的试验与模拟研究
Simulation and Experiments of Laser Bending of Silicon Sheet;
硅片激光弯曲成形的数值模拟及试验
Numerical Simulation of Laser Bending 1Cr17Ni2 Stainless Steel;
1Cr17Ni2不锈钢板料激光弯曲成形数值模拟
Experimental Investigation of Flow Fields in the Curved Common Carotid Artery in Vitro;
弯曲颈总动脉内流场的模拟实验研究
Modeling and Simulation for Bending Stress Analysis of Transmission Gears
变速器齿轮弯曲应力分析建模与仿真
Bending Calculation of Bimodulous Circular Plate under Concentrated Loads
集中载荷作用下双模量圆板弯曲计算
Numerical simulation of flow properties in curving gas vitta
天然气流经弯曲油管柱时的流场模拟
Design of progressive die for the bending sheet based on UG_PDW
基于UG_PDW的弯曲片级进模具设计
The Establishment of the Finite Element Model for Spiral Tube
螺旋盘管弯曲成形有限元模型的建立
Fiber Loop Ring-down Spectroscopy(FLRDS) in Multimode Fiber Bending Loss Measurement
应用FLRDS技术测量多模光纤的弯曲损耗