The molding characteristic of the compression mould for thermoses was analyzed.
分析了热固性塑料压缩模具的成型特点,针对具体的热固性塑料零件,详细介绍了半溢式压缩模具的整体结构和设计要点,为压缩模的设计提供了一定参考。
Calculation of compressive modulus of grid structure -composite foundation;
格栅状复合地基压缩模量的计算
Value determination problem of compressive modulus E_s of soil layers ⑦,⑧ and ⑨ in Shanghai soft soil foundation;
论上海软土地基⑦⑧⑨层压缩模量E_s的定值问题
It was found that gelatin coatings were formed on the pore walls of porous scaffold samples successfully without destroying their porous characteristic,but these coatings improved the compressive strength and compressive modulus o.
复合明胶涂层提高了样品的压缩强度和压缩模量,与未涂覆样品相比,涂敷样品受压时的应变特性发生了明显变化。
Test research on compression modulus of sandy soil tunnel surrounding rock;
砂类土体隧道围岩压缩模量的试验研究
The response to electric field of the composite systems was studied by measure of compression modulus of the elastomers and dynamic-exam of resistance in the cure .
通过对弹性胶体压缩模量的测试和胶凝过程中电阻的动态监测,研究了胶体体系对电场的响应行为。
The compressibility modulus of the dewatering subsidence,sE,is mainly determined by the character diameter of the sand,20D,and the ef.
疏水沉降的侧限压缩模量sE受特征粒径20D和水压降hD控制,20D,hD越大,sE越大;当土样不变时,sE与hD呈正相关关系;当hD一定时,土体的细颗粒含量越多,20D越小,则侧限压缩模量sE越小,土体变形量越大。
Based on settlement data measured in field,compressibility modulus and consolidation coefficient of soil layers are obtained by back analysis method.
基于沉降实测资料,采用反分析方法,确定了各土层的压缩模量和固结系数,并将反演得到的参数代入太沙基一维固结方程,对后续沉降进行预测,从而确定分级压载的下一级压载时间与压载量。
The compression molding process of such long fiber reinforced PP was investigated.
采用粉末浸渍的方法制备连续玻璃纤维增强聚丙烯预浸料,经切割获得长纤维增强聚丙烯粒子,采用单螺杆挤出机挤出形成模塑料,探索了模塑料的压缩模塑成型工艺,研究了成型后材料的力学性能及其影响因素。
A mathematical model of heattransfer in partwas established to simulate thermalbehav- ior of GMT parts during compression molding,coupled with non- isothermal crystallization kinetics of polypropylene.
采用有限元方法 ,对 PP/ GMT制品压缩模塑的冷却与结晶过程进行数值模拟 ,采用非等温结晶模型 ,计算出不同条件下制品中树脂的结晶度和制品内部温度分布 ,并与实验结果进行了对比 ,为压缩模塑中保压冷却时间的确定提供了理论依
The effect of matrix resin,architecture and property of reinforcement,blank design,mold temperature and blank preheat temperature on the fiber distribution during compression molding of glass mat reinforced polypropylene(GMT-PP)was investigated by measuring the fiber content in various areas of GMT-PP after squeezing flow.
通过测定玻璃纤维毡增强聚丙烯经挤压流动后不同区域的纤维含量 ,研究了基体树脂、增强材料的结构与性质、坯料设计、模具温度及坯料的预热温度等对玻璃纤维毡增强聚丙烯在压缩模塑流动过程中纤维分布的影响。
Dessy and Stinky are working on compression
德西和斯丁克写压缩模块代码
When in compact mode, always display on top.
处于压缩模式时，总在顶部显示。
These two parameters are nowadays called the modulus of compressibility.
这两种参数现被称为压缩模量。
Time Compression Mode of Supply Chain Based on the Theory of Constraints;
基于约束理论的供应链时间压缩模式
The H - Squeezed Effects of K - th Power Under the Dual Mode Squeezed Vacuum State;
双模压缩真空态的K次方H压缩效应
full circle expanding hydraulic form
全圆形液压伸缩式模板
Mathematical Model of Displacement Compressor
容积式压缩机数学模型
Analog of Performance of Turbine Compressor
透平式压缩机特性模拟
Reducing military personnel by compressing the scale of the armed forces.
压缩规模，裁减军队员额。
Mathematical Modeling of Rotary Compressors
回转压缩机数学模型
Simulation and Analysis of Interior Flow Field of Scroll Compressor's Compression Chamber
涡旋压缩机压缩腔内部流场的模拟分析
The Fourth-Order Squeezing Effects of Squeezed Even and odd Coherent States
单模压缩奇偶相干态的四次方压缩特性
Fault Diagnosis of Reciprocating Compressor by Using Simulated Cylinder Pressure Curve
往复式压缩机气缸压力模拟曲线提取
Emerge and Utilise of Squeezed Light Field--Experiment on Multimode Squeezing Light Field;
压缩态光场的产生及应用——关于多模压缩态光场的实验
Application and study of discrete model on the compressive mechanism design of compression typed garbage truck
离散模型在压缩式垃圾车压缩机构设计上的应用与研究
Plastics--Determination of compressive elastic modulus
GB/T14694-1993塑料压缩弹性模量的测定
CFD Analysis and Parameterized Modeling of Centrifugal Compressor;
离心压缩机的CFD分析与建模参数化
Dynamic Simulation Research of Air-conditioner Compressor-pipe System;
空调压缩机配管系统的动态模拟研究